XRF4 RF Accessory Kit

by: AMD

The XRF4 RF Accessory Kit is a modular 8-transmit, 8-receive, and 2-feedback RF front end for the Zynq™ UltraScale+™ RFSoC DFE ZCU670 and GEN 3 ZCU208 evaluation boards. The board is supported by AMD DFE Evaluation SW that allows users to quickly and easily evaluated AMD silicon and IP with their chosen RF line up. The modular nature of the kit enables support for a wide range of operating bands and the ability for customers to customize if they wish to develop their own RF front end solutions. The kit comes with RF slices (modules) that support the N77 (3.3–4.2 GHz) wireless access band with support for other wireless bands available from AMD.

Buy

WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP), which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to: www.P65Warnings.ca.gov

Overview

Product Description

The XRF4 RF Accessory Kit includes the XRF4 radio frequency (RF) baseboard (XRF4-RFBB) along with XRF4 RF slices for transmit (TX), receive (RX), and feedback (FB) processing.

The XRF4-RFBB board is the recommended interface board for RF evaluation using the ZCU670 and ZCU208 evaluation boards. This card enables the users to easily add a full RF line up to the RFSoC integrated RF Sampling transceiver. There are nine connectors, also referred to as RF slice connectors, that enable RF line up modules (slices) to be added to the board. These connectors also provide DC power, digital control in the form of the inter-integrated circuit (I2C) protocol, a serial peripheral interface (SPI), general-purpose I/Os (GPIOs), and time division duplex (TDD) control to these RF slice connectors.

The RF slice connectors provide a standard interface the development of RF front-end line ups or RF slices. AMD currently provides RF slices for wireless access (4/5G) targeting FR1 bands, however custom RF line up solutions for various applications, including (but not limited to) FR2 (mmWave), Aerospace, Defense, SATCOM, and Instrumentation can be supported by the RF slice connectors. The AMD Kria™ K26 system-on-module (SOM) acts as the RF controller for the XRF4 baseboard. An onboard physical-side interface (PHY) allows the RF controller to be configured and commanded through Ethernet.

Target Applications:

  • Wireless: 4G LTE, 5G NR use cases
  • Remote PHY for cable access
  • Early warning phased array radar / digital array radar
  • Satellite communications
  • Test & measurement
  • All high-performance RF applications

Key Features & Benefits

Rapid Application Development

  • Equipped with 9 RF slice locations (8T8R2FB) controlled by a Kria K26 SOM running RF controller software.
  • Standard connectors that support timely development of custom RF line up for evaluation

Flexible Multiband Support

  • Range of FR1 bands supported by AMD RF slice options (contact Factory)

Ease of Use

  • DFE Evaluation SW supports AMD Silicon and IP (CFR/DPD) testing with full RF line up see DFE Evaluation Tool

Product Information

Specifications

Board Features

Featuring the XRF4-RFBB

Zynq UltraScale+ XCZU29DR-2FFVF1760 RFSoC CAllout
Kit Specifications Value
Height 14.150 inches (35.941 cm)
Length 4.925 inches (12.510 cm)
No. of RF Slice Connectors 9
Operating Environmental Temperature 0C to +45C
Storage Environmental Temperature -25C to +60C
RF Slices
Height 1.500 inches (3.810 cm)
Length 3.180 inches (8.077 cm)
Configuration
MicroSD Yes
Control I/O
User Pushbuttons 3
DIP Switches 4
User LEDs 4
System Controller Yes
What’s Inside

What's Inside the Box

Featuring the Zynq™ UltraScale+™ RFSoC XRF4 Baseboard

2188650_XRF4_3342_Whats_Inside_Graphic_2000x1059

Resources

Documentation

Featured Documents & Tutorials

Default Default Title Document Type Date
Tools
  • DFE Demo Lounge: Digital Front-End Radio Demo Evaluation Secure Site containing DFE Demo general information and software files.
  • RFSOC DFE Eval Platform Lounge: Zynq™ UltraScale+™ RFSoC DFE Evaluation Platform Secure Site containing the latest information available for the Zynq RFSoC DFE to support your evaluation and design activities.  
Get Started

Get Started with the ZCU208 and ZCU670

The XRF4 is intended to be used as a companion to the ZCU208 and ZCU670 boards. For instructions on how to get started, visit the Lounges linked in the Tools tab.

Training & Support